- 您現在的位置：買賣IC網 > PDF目錄368914 > 25AA040X-IST Evaluation Kit for the MAX1698 PDF資料下載
參數資料
| 型號： | 25AA040X-IST |
| 英文描述： | Evaluation Kit for the MAX1698 |
| 中文描述： | SPI串行EEPROM |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 160K |
| 代理商： | 25AA040X-IST |
25AA040/25LC040/25C040
1998 Microchip Technology Inc.
DS21204B-page 9
3.5
Read Status Register (RDSR)
The RDSR instruction provides access to the status
register. The status register may be read at any time,
even during a write cycle. The status register is format-
ted as follows:
The
Write-In-Process (WIP)
bit indicates whether the
25xx040 is busy with a write operation. When set to a
‘1’ a write is in progress, when set to a ‘0’ no write is in
progress. This bit is read only.
The
Write Enable Latch (WEL)
bit indicates the sta-
tus of the write enable latch. When set to a ‘1’ the latch
allows writes to the array, when set to a ‘0’ the latch
prohibits writes to the array. The state of this bit can
always be updated via the WREN or WRDI commands
regardless of the state of write protection on the status
register. This bit is read only.
The
Block Protection (BP0 and BP1)
bits indicate
which blocks are currently write protected. These bits
are set by the user issuing the WRSR instruction.
These bits are non-volatile.
See Figure 3-8 for RDSR timing sequence
3.6
Write Status Register(WRSR)
The WRSR instruction allows the user to select one of
four levels of protection for the array by writing to the
appropriate bits in the status register. The array is
divided up into four segments. The user has the ability
to write protect none, one, two, or all four of the seg-
ments of the array. The partitioning is controlled as
illustrated in Table 3-7.
See Figure 3-9 for WRSR timing sequence
TABLE 3-7:
ARRAY PROTECTION
FIGURE 3-8:
READ STATUS REGISTER SEQUENCE
FIGURE 3-9:
WRITE STATUS REGISTER SEQUENCE
7
X
6
X
5
X
4
X
3
2
1
0
BP1
BP0
WEL
WIP
BP1
BP0
Array Addresses
Write Protected
0
0
none
upper 1/4
(0180h - 01FFh)
upper 1/2
(0100h - 01FFh)
all
(0000h - 01FFh)
0
1
1
0
1
1
SO
SI
CS
9
10
11
12
13
14
15
1
1
0
0
0
0
0
0
7
6
5
4
2
1
0
instruction
data from status register
high impedance
SCK
0
2
3
4
5
6
7
1
8
3
SO
SI
CS
9
10
11
12
13
14
15
0
1
0
0
0
0
0
0
7
6
5
4
2
1
0
instruction
data to status register
high impedance
SCK
0
2
3
4
5
6
7
1
8
3
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料 |
PDF描述 |
|---|---|
| 25AA040X-ST | Evaluation Kit for the MAX1700, MAX1701 |
| 25AA040XT-EST | Evaluation Kit for the MAX1702B |
| 25AA040XT-IST | Evaluation Kit for the MAX1703 |
| 25C040EN | EEPROM |
| 25C040-EP | Evaluation Kit for the MAX1744, MAX1745 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 25AA040X-ST | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM |
| 25AA040XT | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:4K SPI Bus Serial EEPROM |
| 25AA040XT/ST | 功能描述:電可擦除可編程只讀存儲器 512x8 - 1.8V Rot Pin RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 25AA040XT-EST | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM |
| 25AA040XT-I/ST | 功能描述:電可擦除可編程只讀存儲器 512x8 - 1.8V Rot Pin RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。